Dwyer Instruments 2300-10MM
Magnehelic Differential Pressure Gauge, 5-0-5 mm H2O

Order #: 2300-10MM

Mfg #: 2300-10MM

Questions about availability or need help? Contact Us:

(800) 633-0561
$86.00

Dwyer Instruments 2300-10MM

Magnehelic Differential Pressure Gauge, 5-0-5 mm H2O

Order #: 2300-10MM

Mfg #: 2300-10MM

$86.00

Using Dwyer's simple, frictionless Magnehelic gage movement, it quickly indicates low air or non-corrosive gas pressures--either positive, negative (vacuum) or differential. The design resists shock, vibration and over-pressures. No manometer fluid to evaporate, freeze or cause toxic or leveling problems. It's inexpensive, too.

Availability: Ships in 3-4 weeks

Choose Your Options:

Add Calibration

You have chosen to add the following Calibration Services to Your Order

Make sure your instrument is calibrated and ready to use the minute you open the box by adding our expert calibration service. Why Calibrate? For a complete descriptions of Transcat Service Levels, click here.

Already have this this item and need calibration? Request a calibration quote

This product is available for shipping to the United States and Canada only.

The Magnehelic gage is the industry standard to measure fan and blower pressures, filter resistance, air velocity, furnace draft, pressure drop across orifice plates, liquid levels with bubbler systems and pressures in fluid amplifier or fluidic systems. It also checks gas-air ratio controls and automatic valves, and monitors blood and respiratory pressures in medical care equipment.

Blowout plug is comprised of a rubber plug on the rear which functions as a relief valve by unseating and venting the gage interior when over pressure reaches approximately 25 psig (1.7 bar). To provide a free path for pressure relief, there are four spacer pads which maintain 0.023" clearance when gage is surface mounted. Do not obstruct the gap created by these pads. The blowout plug is not used on models above 180" of water pressure, medium or high pressure models, or on gages which require an elastomer other than silicone for the diaphragm. The blowout plug should not be used as a system overpressure control. High supply pressures may still cause the gage to fail due to over pressurization, resulting in property damage or serious injury. Good engineering practices should be utilized to prevent your system from exceeding the ratings or any component. O-ring seal for cover assures pressure integrity of case. Samarium Cobalt magnet mounted at one end of range spring rotates helix without mechanical linkages.

Product Highlights

  • Bezel provides flange for flush mounting in panel
  • Clear plastic face is highly resistant to breakage
  • It reacts to pressure on diaphragm
  • Live length adjustable for calibration
  • Silicone rubber diaphragm with integrally molded O-ring is supported by front and rear plates
  • Provides undistorted viewing of pointer and scale
  • Precision litho-printed scale is accurate and easy to read
  • Red tipped pointer of heat treated aluminum tubing is easy to see
  • It is rigidly mounted on the helix shaft
  • Pointer stops of molded rubber prevent pointer over-travel without damage
  • "Wishbone" assembly provides mounting for helix, helix bearings and pointer shaft
  • Jeweled bearings are shock-resistant mounted; provide virtually friction-free motion for helix
  • Motion damped with high viscosity silicone fluid
  • Zero adjustment screw is conveniently located in the plastic cover, and is accessible without removing the cover
  • O-ring seal provides pressure tightness
  • Helix is precision made from an alloy of high magnetic permeability
  • Mounted in jeweled bearings, it turns freely, following the magnetic field to move the pointer across the scale
  • Calibrated range spring is flat spring steel
  • Small amplitude of motion assures consistency and long life
  • It is locked and sealed in position with a sealing plate and retaining ring
  • Diaphragm motion is restricted to prevent damage due to overpressures
  • Die cast aluminum case is precision made and iridite-dipped to withstand 168 hour salt spray corrosion test
  • Exterior finished in baked dark gray hammerloid
  • One case size is used for all standard pressure options, and for both surface and flush mounting
  • Overpressure Protection
  • 5-0-5 mm H2O
Win a Generac Generator when purchasing $750 or more from Transcat.Win a Generac Generator when purchasing $750 or more from Transcat.
All products in this series
  1. Dwyer Instruments 2300-3KPA
    Dwyer Instruments 2300-3KPA
    Magnehelic Differential Pressure Gauge, 1.5-0-1.5 kPa
    $86.00
  2. Dwyer Instruments 2300-250PA
    Dwyer Instruments 2300-250PA
    Magnehelic Differential Pressure Gauge, 125-0-125 Pa
    $88.75
  3. Dwyer Instruments 2000-00
    Dwyer Instruments 2000-00
    Magnehelic Differential Pressure Gauge, 0-0.25 in H2O
    $87.20
  4. Dwyer Instruments 2000-0-ASF
    Dwyer Instruments 2000-0-ASF
    Magnehelic Diff. Press. Gauge 0-.50 in H2O, adj. signal flag
    $90.75
  5. Dwyer Instruments 2300-1KPA
    Dwyer Instruments 2300-1KPA
    Magnehelic Differential Pressur Gauge, 0.5-0-0.5 kPa
    $86.00
  6. Dwyer Instruments 2300-500PA
    Dwyer Instruments 2300-500PA
    Magnehelic Differential Pressure Gauge, 250-0-250 Pa
    $86.00
  7. Dwyer Instruments 2000-0-SP
    Dwyer Instruments 2000-0-SP
    Magnehelic Pressure Gauge 0-.5 in H2O,set point indicator
    $259.00
  8. Dwyer Instruments 2300-20MM
    Dwyer Instruments 2300-20MM
    Magnehelic Differential Pressure Gauge, 10-0-10 mm H2O
    $88.75
  9. Dwyer Instruments 2300-30CM
    Dwyer Instruments 2300-30CM
    Magnehelic Differential Pressure Gauge, 15-0-15 cm H2O
    $95.20
  10. Dwyer Instruments 2300-120PA
    Dwyer Instruments 2300-120PA
    Magnehelic Differential Pressur Gauge, 60-0-60 Pa
    $86.00